× We have recently moved to a new server. If you run into any issues, please let us know through the Contact Us link at the bottom of the page. Thanks for visiting RocketReviews.

Scratch MMX Sputnik Original Design / Scratch Built

Scratch - MMX Sputnik {Scratch}

Contributed by Clive Davis

Manufacturer: Scratch
(Contributed - by Clive Davis - 06/25/06) (Scratch) MMX Sputnik

Brief:
This is a Micromaxx version of the old Sputnik model rocket that used dowels and a styrofoam ball.

Construction:
My MMX Sputnik requires:

  • 1 styrofoam ball (approx. 1" in diameter)
  • 3 toothpicks
  • 1 piece of fiberboard (for the foot pods)
  • 1 small piece of T2+ body tube
  • 1 small piece of MMX style launch lug
  • decals and paint as necessary

My wife had picked up a bunch of stuff from Michael's recently for projects for my 3-year old. I found a bag of small styrofoam balls and immediately I knew what I had to do.

(Scratch) MMX Sputnik I took the styrofoam and used a small metal file to create a hole big enough for the BT2+ to fit inside. This is the motor mount. I pushed it into the styrofoam (trying to center it), and then removed it to release the loose styrofoam. Next, I glued the tube in place.

After the motor mount had dried, I took the launch lug and pushed it along side the motor mount until it poked through the top of the styrofoam. I simply cut the launch lug to an appropriate size and then glued it to the motor mount and styrofoam.

Next, I trimmed one of the pointy ends off of each toothpick. I pushed the pointy end into the styrofoam, approximately 120 degrees apart, with the toothpicks angling outwards. Once I was sure that the toothpicks were at the right angle and the correct length, I glued them in place.

I used a hole puncher to create three small disks from the black fiber board. When building a few FlisKits models recently, I kept some of the black fiberboard from the middle of the centering rings and placed them in my parts bin. These small disks I created are meant to be little pods at the end of the Sputnik. I simply glued these on to the ends of the toothpicks, making sure they were rather flat so the Sputnik could stand up nicely.

(Scratch) MMX Sputnik

Finishing:
After everything was dry, I gave the rocket a good coating of silver paint. I used acrylic paint and my airbrush. The solvents in the Krylon-style paint are not good for this project as they will melt the styrofoam.

Once the silver was dry, I simply dipped each "foot" into a bath of red acrylic paint and let the whole thing dry. I used sticky decals from my excess decals bin to add more details on my Sputnik. I then clear coated the rocket with Future Floor Polish.

Flight:
Prepping is simple. There is no recovery device. All I had to do was put a MMX motor in the rocket and attach igniter and clips. I have had one flight so far, but this thing really zoomed off the pad nicely. For a Sputnik (high drag), it has some respectable altitude. I was very pleased with the results. Next, I have to make a few more launches so that I can repeat my success.

The rocket did spit the motor. On my MMX Sputnik, there actually is part of the body tube beneath the styrofoam, so I could tape the motor to the rocket. I think I will try this for the next launch.

Recovery:
There was some slight blackening under the MMX Sputnik, but nothing threatening or out of the ordinary. Also, the rocket is a tad hard to find since it is small. Have some extra pair of eyes with you when you launch it.

Summary:
PROs: Cheap and easy build. Get a few styrofoam balls and build these with your children.

CONs: I can't really think of any.

comment Post a Comment