All Rocketry Blogs

 Rocketry Product: Semroc - Little Joe II {Kit} (KS-3)

Rocket Dungeon: Opened my Semroc Little Joe II (2010-08-15)

My Semroc order arrived while I was launching yesterday.  2 1/2 day turnaround - great for mere mortals, but a day slower than my previous order.  Anyway, most of what I got was just to put ... [Read More]

Model Rocket Building: Semroc Little Joe II Build Part 1 Parts (2010-09-17)

On to the next rocket in the build pile - The Semroc LITTLE JOE II I built and flew the Estes kit in the early 1970s, this version seems very close, except for all the laser cut balsa and thick card ... [Read More]

Model Rocket Building: Semroc Little Joe II Build Part 2 Engine Mount (2010-09-17)

Nothing out of the ordinary here. A standard engine mount, the centering rings fit perfectly. I use black electrical tape instead of masking tape to hold the engine hook in place. If you've ever ... [Read More]

Model Rocket Building: Semroc Little Joe II Build Part 3 Fins (2010-09-19)

Sorry, I wasn't able to get online yesterday to do blog entries. Once again, AT&T Internet was down. Last month it was down for a day. Two strikes for AT&T, one more and they are OUT! Back ... [Read More]

Model Rocket Building: Semroc Little Joe II Part 4 Fins (2010-09-19)

In step 9 you cease the fin cover down it's center line . Some vendors will direct you to cut halfway through the stock with a sharp knife. I've never found that necessary and you run the risk of ... [Read More]

Model Rocket Building: Semroc Little Joe II Build Part 5 Fins (2010-09-20)

Here's the ribs glued into one side of the fin cover. The instructions are right - use just a little glue to set the ribs in place. Too much and it could distort the other side of the cardstock ... [Read More]

Model Rocket Building: Semroc Little Joe II Build Part 6 Fins (2010-09-20)

Okay - everything was going well up until now . I was only happy with the way one fin out of four turned out. I was careful not to use much glue to attach the internal balsa ribs, but I still had ... [Read More]

Model Rocket Building: Semroc Little Joe II Build Part 7 Body Wraps (2010-09-21)

I built a little out of order from the instructions. The wraps actually should have been put on before the fins were made. While the instructions say to use glue to attach the wraps to the body ... [Read More]

Model Rocket Building: Semroc Little Joe II Build Part 9 Engine Mount Install (2010-09-21)

The tube is marked for the fins by placing the body tube on top of a marking guide. You are told to mark the fin lines between two of the corrugations. I found it hard to do this. I ended up just ... [Read More]

Model Rocket Building: Semroc Little Joe II Build Part 10 Pre-Paint (2010-09-22)

The fins were glued on and fillets applied. I tried to pre-plan the fin alignment lines, one was drawn on the lower wrap seam to partially cover it up. To center the launch lug on the upper wrap: ... [Read More]

Model Rocket Building: Semroc Little Joe II Build Paint and Decals (2010-09-22)

The lower body was painted using WalMart Colorplace Aluminum. It's one of the better, cheap paints, around $1.00 a can. Remember those extra trim decals I printed up awhile back? Click HERE for an ... [Read More]

Model Rocket Building: Semroc Little Joe II Part 11 Apollo Capsule Kit (2010-09-23)

The 1/70 Scale Apollo capsule kit is included in the Little Joe kit bag. This brings back memories from the time I tackled the Estes Saturn 1B in the mid 1970s! I hope to do a better job of it this ... [Read More]

Model Rocket Building: Semroc Little Joe Build Part 11 Capsule Parts (2010-09-23)

Here's all the capsule and tower parts. And, a close up of the unusual pieces. The two balsa ends of the escape tower motor unit are one piece and are cut apart. You aren't told to cut them apart in ... [Read More]

Model Rocket Building: Semroc Little Joe II Build Part 12 Command Module (2010-09-23)

One of the more unusual parts is the large ring on the laser cut sheet. You can see how thick the outside cut seems to be. The two slots under the ring are the diameter guides for the tower dowels. ... [Read More]

Model Rocket Building: Semroc Little Joe II build Part 13 Command Module (2010-09-23)

The shroud has been formed the large ring edge tapered. Here's a top view of the assembled parts up to step 7. The escape tower motor unit (Step 2) isn't glued together yet, clay nose weight will go ... [Read More]

Model Rocket Building: Semroc Little Joe II Build Part 13 Tower (2010-09-24)

In Step 8, two of the four 1/12" diameter dowels are sanded down to .058 diameter. The other two are sanded to a new diameter of .041. On the laser cut card stock sheet there are "feeler gauges" to ... [Read More]

Model Rocket Building: Semroc Little Joe II Build Part 14 Tower (2010-09-24)

Take a close look at the Semroc tower pattern. With a pencil and straightedge I've extended the cut lines past what was printed on the pattern. This makes cutting the dowel length and angles easier. ... [Read More]

Model Rocket Building: Semroc Little Joe II Build Part 15 Tower (2010-09-28)

The best recommendation I can give you on the tower is to take the extra few moments to get the strut end angles correct. It's a fine line here - you want a slight friction fit between the two ... [Read More]

Model Rocket Building: Semroc Little Joe II Part 16 Tower (2010-09-29)

Here's the tower sides, all four glued together. One thing I learned after the tower sides were glued - every other "Z" diagonal brace side should be reversed as shown in this drawing. (Click on the ... [Read More]

Model Rocket Building: Semroc Little Joe II Build Part 17 Tower (2010-09-30)

The Semroc instructions have you glue the tower onto the Command Module capsule before the V strut assemblies are in place. I found it easier to glue them in place now. Looking ahead, I wanted to ... [Read More]

Model Rocket Building: Semroc Little Joe II Build Part 18 Tower (2010-09-30)

No doubt about it, the tower is a tough build! The outside four sides weren't hard to glue up, but the inside V strut assembly took too much effort. Earlier, the O ring (in the middle) was split and ... [Read More]

Rocket Dungeon: I blame Chris (my first LJ II post) (2010-10-01)

At least I will some time tomorrow.  That is, after reading and enjoying his detailed posts on the Semroc Little Joe II , I decided to start mine.  The body is moving along well and really ... [Read More]

Model Rocket Building: Semroc Little Joe II Part 19 Tower Nozzles (2010-10-01)

In Step 18, the four escape motor nozzles are made. The shape of the nozzles on the shroud sheet look strange. That "S" shaped wavy inside line gives you the correct angle when gluing underneath the ... [Read More]

Model Rocket Building: Semroc Little Joe II Part 20 Paint Plan (2010-10-02)

I couldn't quite understand the Semroc painting instructions. I went over to JimZs site for the Estes Little Joe painting information: http://www.spacemodeling.org/JimZ/estes/k-30.pdf Scroll down to ... [Read More]

Model Rocket Building: Little Joe II Part 21 Tower and Vanes (2010-10-03)

I have to back track a little here - In Step 14, you set the lower end of the tower jig on the top of the capsule. Using a dowel, you make "half-holes" by pressing the dowel into the balsa. You have ... [Read More]

Model Rocket Building: Little Joe II Part 22 Tower Painting (2010-10-03)

I mentioned earlier that the tower would be painted in sub assembles and then glued together. Understand when building this way, you do compromise some strength of the tower by gluing after ... [Read More]

Model Rocket Building: Semroc Little Joe Part 23 Capsule Paint (2010-10-04)

Before the capsule was painted silver, I pushed small squares of masking tape in the half-circle indentations made earlier. This will keep the paint out and give just a little more gluing area. ... [Read More]

Model Rocket Building: Semroc Little Joe II Part 24 Tower (2010-10-05)

The black tower skirt took a lot of adjustments to get straight. Like I did before on the tower bottom, four different 90 degree turns were checked to find the best upright position BT-3 escape ... [Read More]

Model Rocket Building: Semroc Little Joe FINISHED! (2010-10-06)

A long, but rewarding build. Not my best work, but certainly better than my first Estes Little Joe build in the mid 1970s. One day soon I'll have the courage to fly it. For now, it's ... [Read More]

Rocket Dungeon: Review: Semroc Little Joe II (2011-03-22)

This 1/70 scale Little Joe II is one of Semroc’s “Retro-Repro” line of kits. It includes a separately bagged Apollo capsule kit and is billed as a Skill Level-4 “Master” kit. The base ... [Read More]

Rocket Dungeon: Already antsy to launch, building is in the doldrums (2010-09-25)

A mere week after ESL-148, I'm already itching to launch.  My October launches are still up in the air and the prospects of missing them is fueling the itch.  I have NARHAMS and then Red ... [Read More]

Rocket Dungeon: Countin' my chickens before they hatch FLY (2011-03-18)

The literal count is one, one Ballistic Chicken. But what I was getting at in the title is that I have laid out and prepped my rockets for tomorrow; and I even built a couple of reloads.  Last ... [Read More]

Rocket Dungeon: Launch Report 2011-01 (2011-03-20)

Location: Price, MD ( MDRA ESL-154) Weather: partly cloudy, low 50's, wind 0 - 5 MPH Total flights: Today - 11; YTD - 11 Total motors: Today - 21; YTD - 21 I left very early under the light of the ... [Read More]

Model Rocket Building: Saturn Towers (2011-06-21)

I've built a lot of towers over the years. For comparison, here's the Saturn towers from various kits. On the upper left is the BT-20 based Dr. Zooch Saturn V tower. It's really a silhouette tower, ... [Read More]